-
2019.07.22
Updated firmware for mightyZAP 96mm stroke Premium lineup is just release. To optimize your mightyZAP performance, you are strongly requested to update your old version firmware.
Make sure to download correct model named firmware for your mightyZAP. Download the concerned firmware correctly according to your servo model.
Refer to the update manual. [Manual download]
For firmware update, make sure to install 'mightyZAP manager' software v.1.0.7 on your PC and you need to have IR-USB01 PC USB interface for PC connection.
For those who use older version mightyZAP manager software, here is the download link for 'mightyZAP manager' software v.1.0.7.
Caution
Make sure to download correct model named firmware for your mightyZAP. Download the concerned firmware correctly according to your servo model.
Update single servo only. Do not update with multiple qty of servo motor under serial connection(daisy chain) at the same time. Otherwise, it may occur some error.
In case that incorrect firmware is installed, please process the update with correct firmware update file again.
Before update, make sure if all wirings (communication wire, power wire) are properly connected between IR-USB01 & Servo / between PC and IR-USB01. Then, please do not touch them while updating as it may occur fatal communication error. Please contact factory if communication or update error continues.
From this update, stroke calibration process is added after firmware update. So, before firmware update, make sure if actuator is standalone(should not be connected with any mechanical stuff of your application) for proper calibration.
What are updated?
Before
After
What are updated?
OVERLOAD Protection
Different overload spec per each model
All models overload protection standard are unified and motor cut off under below conditions ;
Continuous operation for more than 30sec. or,
Actuator is stuck at certain point for more than 30sec without position change after goal position command.
Overload protection improvement
Force limit feature removal
Force limit feature (volatile parameter)
Force limit feature removal
To be removed as “Max force”(Non-volatile data) parameter has same function.
“Max force” name change
Previous name has been “Max force”
New name “Motor Operating rate”
To provide more exact definition of this feature
“Motor operating rate” range change
Previously 0~1023 (under the Max force feature)
New range : 400~1023
To be changed to actual operating range.
“Speed” Parameter Removal
Unnatural speed adjustment by Speed parameter
Speed adjustment by “Motor operating rate”. (Force and speed will be adjusted at the same time)
More smooth speed adjustment.
Compliance margin
Compliance margin
Segmentalized to “Start compliance margin” and “End compliance margin”
Improved Stability of position control
Calibration process
Calibration process after firmware update.
Secure exact stroke range
Check Firmware version
Please refer to the old and new firmware number for each servo model.
Firmware version number can be found on mightyZAP manager software. Connect your actuator with software, then see "Management"-"Information" window or "System"-"Firmware version".
If your firmware version is old version, please update it for better performance. (The firmware of actuators which have been delivered after the "Applied" date are already updated. But for sure, please check the firmware version on mightyZAP manager software.)
Old Ver.
New Ver.
Applied
(적용일)
L12-20PT-10
Ver. 1
Ver. 2
30-May-19
L12-30PT-10
Ver. 1
Ver. 2
05-Jun-19
L12-20F-10
Ver. 1
Ver. 2
30-May-19
L12-30F-10
Ver. 1
Ver. 2
05-Jun-19
the end.
-
2019.07.22
Updated firmware for mightyZAP 56mm stroke Premium lineup is just release. To optimize your mightyZAP performance, you are strongly requested to update your old version firmware.
Make sure to download correct model named firmware for your mightyZAP. Download the concerned firmware correctly according to your servo model.
Refer to the update manual. [Manual download]
For firmware update, make sure to install 'mightyZAP manager' software v.1.0.7 on your PC and you need to have IR-USB01 PC USB interface for PC connection.
For those who use older version mightyZAP manager software, here is the download link for 'mightyZAP manager' software v.1.0.7.
Caution
Make sure to download correct model named firmware for your mightyZAP. Download the concerned firmware correctly according to your servo model.
Update single servo only. Do not update with multiple qty of servo motor under serial connection(daisy chain) at the same time. Otherwise, it may occur some error.
In case that incorrect firmware is installed, please process the update with correct firmware update file again.
Before update, make sure if all wirings (communication wire, power wire) are properly connected between IR-USB01 & Servo / between PC and IR-USB01. Then, please do not touch them while updating as it may occur fatal communication error. Please contact factory if communication or update error continues.
From this update, stroke calibration process is added after firmware update. So, before firmware update, make sure if actuator is standalone(should not be connected with any mechanical stuff of your application) for proper calibration.
What are updated?
Before
After
What are updated?
OVERLOAD Protection
Different overload spec per each model
All models overload protection standard are unified and motor cut off under below conditions ;
Continuous operation for more than 30sec. or,
Actuator is stuck at certain point for more than 30sec without position change after goal position command.
Overload protection improvement
Force limit feature removal
Force limit feature (volatile parameter)
Force limit feature removal
To be removed as “Max force”(Non-volatile data) parameter has same function.
“Max force” name change
Previous name has been “Max force”
New name “Motor Operating rate”
To provide more exact definition of this feature
“Motor operating rate” range change
Previously 0~1023 (under the Max force feature)
New range : 400~1023
To be changed to actual operating range.
“Speed” Parameter Removal
Unnatural speed adjustment by Speed parameter
Speed adjustment by “Motor operating rate”. (Force and speed will be adjusted at the same time)
More smooth speed adjustment.
Compliance margin
Compliance margin
Segmentalized to “Start compliance margin” and “End compliance margin”
Improved Stability of position control
Calibration process
Calibration process after firmware update.
Secure exact stroke range
Check Firmware version
Please refer to the old and new firmware number for each servo model.
Firmware version number can be found on mightyZAP manager software. Connect your actuator with software, then see "Management"-"Information" window or "System"-"Firmware version".
If your firmware version is old version, please update it for better performance. (The firmware of actuators which have been delivered after the "Applied" date are already updated. But for sure, please check the firmware version on mightyZAP manager software.)
Old Ver.
New Ver.
Applied
(적용일)
L12-20PT-6
Ver. 1
Ver. 2
30-May-19
L12-30PT-6
Ver. 1
Ver. 2
05-Jun-19
L12-50PT-6
Ver. 1
Ver. 2
30-May-19
L12-80PT-6
Ver. 1
Ver. 2
30-May-19
L12-20F-6
Ver. 1
Ver. 2
30-May-19
L12-30F-6
Ver. 1
Ver. 2
05-Jun-19
L12-50F-6
Ver. 1
Ver. 2
30-May-19
L12-80F-6
Ver. 1
Ver. 2
30-May-19
The end.
-
2019.07.22
Updated firmware for mightyZAP 41mm stroke Premium lineup is just release. To optimize your mightyZAP performance, you are strongly requested to update your old version firmware.
Make sure to download correct model named firmware for your mightyZAP. Download the concerned firmware correctly according to your servo model.
Refer to the update manual. [Manual download]
For firmware update, make sure to install 'mightyZAP manager' software v.1.0.7 on your PC and you need to have IR-USB01 PC USB interface for PC connection.
For those who use older version mightyZAP manager software, here is the download link for 'mightyZAP manager' software v.1.0.7.
Caution
Make sure to download correct model named firmware for your mightyZAP. Download the concerned firmware correctly according to your servo model.
Update single servo only. Do not update with multiple qty of servo motor under serial connection(daisy chain) at the same time. Otherwise, it may occur some error.
In case that incorrect firmware is installed, please process the update with correct firmware update file again.
Before update, make sure if all wirings (communication wire, power wire) are properly connected between IR-USB01 & Servo / between PC and IR-USB01. Then, please do not touch them while updating as it may occur fatal communication error. Please contact factory if communication or update error continues.
From this update, stroke calibration process is added after firmware update. So, before firmware update, make sure if actuator is standalone(should not be connected with any mechanical stuff of your application) for proper calibration.
What are updated?
Before
After
What are updated?
OVERLOAD Protection
Different overload spec per each model
All models overload protection standard are unified and motor cut off under below conditions ;
Continuous operation for more than 30sec. or,
Actuator is stuck at certain point for more than 30sec without position change after goal position command.
Overload protection improvement
Force limit feature removal
Force limit feature (volatile parameter)
Force limit feature removal
To be removed as “Max force”(Non-volatile data) parameter has same function.
“Max force” name change
Previous name has been “Max force”
New name “Motor Operating rate”
To provide more exact definition of this feature
“Motor operating rate” range change
Previously 0~1023 (under the Max force feature)
New range : 400~1023
To be changed to actual operating range.
“Speed” Parameter Removal
Unnatural speed adjustment by Speed parameter
Speed adjustment by “Motor operating rate”. (Force and speed will be adjusted at the same time)
More smooth speed adjustment.
Compliance margin
Compliance margin
Segmentalized to “Start compliance margin” and “End compliance margin”
Improved Stability of position control
Calibration process
Calibration process after firmware update.
Secure exact stroke range
Check Firmware version
Please refer to the old and new firmware number for each servo model.
Firmware version number can be found on mightyZAP manager software. Connect your actuator with software, then see "Management"-"Information" window or "System"-"Firmware version".
If your firmware version is old version, please update it for better performance. (The firmware of actuators which have been delivered after the "Applied" date are already updated. But for sure, please check the firmware version on mightyZAP manager software.)
Old Ver.
New Ver.
Applied
(적용일)
L12-20PT-4
Ver. 1
Ver. 2
05-Jun-19
L12-30PT-4
Ver. 1
Ver. 2
30-May-19
L12-50PT-4
Ver. 1
Ver. 2
30-May-19
L12-80PT-4
Ver. 1
Ver. 2
30-May-19
L12-20F-4
Ver. 1
Ver. 2
05-Jun-19
L12-30F-4
Ver. 1
Ver. 2
30-May-19
L12-50F-4
Ver. 1
Ver. 2
30-May-19
L12-80F-4
Ver. 1
Ver. 2
30-May-19
The end.
-
2019.07.22
Updated firmware for mightyZAP 27mm(30mm) stroke Premium lineup is just release. To optimize your mightyZAP performance, you are strongly requested to update your old version firmware.
Make sure to download correct model named firmware for your mightyZAP. Download the concerned firmware correctly according to your servo model.
Refer to the update manual. [Manual download]
For firmware update, make sure to install 'mightyZAP manager' software v.1.0.7 on your PC and you need to have IR-USB01 PC USB interface for PC connection.
For those who use older version mightyZAP manager software, here is the download link for 'mightyZAP manager' software v.1.0.7.
Caution
Make sure to download correct model named firmware for your mightyZAP. Download the concerned firmware correctly according to your servo model.
Update single servo only. Do not update with multiple qty of servo motor under serial connection(daisy chain) at the same time. Otherwise, it may occur some error.
In case that incorrect firmware is installed, please process the update with correct firmware update file again.
Before update, make sure if all wirings (communication wire, power wire) are properly connected between IR-USB01 & Servo / between PC and IR-USB01. Then, please do not touch them while updating as it may occur fatal communication error. Please contact factory if communication or update error continues.
From this update, stroke calibration process is added after firmware update. So, before firmware update, make sure if actuator is standalone(should not be connected with any mechanical stuff of your application) for proper calibration.
What are updated?
Before
After
What are updated?
OVERLOAD Protection
Different overload spec per each model
All models overload protection standard are unified and motor cut off under below conditions ;
Continuous operation for more than 30sec. or,
Actuator is stuck at certain point for more than 30sec without position change after goal position command.
Overload protection improvement
Force limit feature removal
Force limit feature (volatile parameter)
Force limit feature removal
To be removed as “Max force”(Non-volatile data) parameter has same function.
“Max force” name change
Previous name has been “Max force”
New name “Motor Operating rate”
To provide more exact definition of this feature
“Motor operating rate” range change
Previously 0~1023 (under the Max force feature)
New range : 400~1023
To be changed to actual operating range.
“Speed” Parameter Removal
Unnatural speed adjustment by Speed parameter
Speed adjustment by “Motor operating rate”. (Force and speed will be adjusted at the same time)
More smooth speed adjustment.
Compliance margin
Compliance margin
Segmentalized to “Start compliance margin” and “End compliance margin”
Improved Stability of position control
Calibration process
Calibration process after firmware update.
Secure exact stroke range
Check Firmware version
Please refer to the old and new firmware number for each servo model.
Firmware version number can be found on mightyZAP manager software. Connect your actuator with software, then see "Management"-"Information" window or "System"-"Firmware version".
If your firmware version is old version, please update it for better performance. (The firmware of actuators which have been delivered after the "Applied" date are already updated. But for sure, please check the firmware version on mightyZAP manager software.)
Old Ver.
New Ver.
Applied
(적용일)
L7-20PT-3
Ver. 5
Ver. 6
04-Jun-19
L7-40PT-3
Ver. 4
Ver. 5
04-Jun-19
L7-64PT-3
Ver. 3
Ver. 4
04-Jun-19
L7-100PT-3
Ver. 3
Ver. 4
04-Jun-19
L12-12PT-3
-
Ver. 1
05-Jun-19
L12-12F-3
-
Ver. 1
05-Jun-19
L12-20PT-3
Ver. 6
Ver. 7
29-May-19
L12-40PT-3
Ver. 4
Ver. 5
29-May-19
L12-64PT-3
Ver. 3
Ver. 4
30-May-19
L12-100PT-3
Ver. 3
Ver. 4
30-May-19
L12-20F-3
Ver. 4
Ver. 5
29-May-19
L12-40F-3
Ver. 4
Ver. 5
29-May-19
L12-64F-3
Ver. 3
Ver. 4
29-May-19
L12-100F-3
Ver. 3
Ver. 5
30-May-19
The end.
-
2019.07.22
Updated firmware for mightyZAP 27mm(30mm) stroke Economical lineup is just release. To optimize your mightyZAP performance, you are strongly requested to update your old version firmware.
Make sure to download correct model named firmware for your mightyZAP. Download the concerned firmware correctly according to your servo model.
Refer to the update manual. [Manual download]
For firmware update, make sure to install 'mightyZAP manager' software v.1.0.7 on your PC and you need to have IR-USB01 PC USB interface for PC connection.
For those who use older version mightyZAP manager software, here is the download link for 'mightyZAP manager' software v.1.0.7.
Caution
Make sure to download correct model named firmware for your mightyZAP. Download the concerned firmware correctly according to your servo model.
Update single servo only. Do not update with multiple qty of servo motor under serial connection(daisy chain) at the same time. Otherwise, it may occur some error.
In case that incorrect firmware is installed, please process the update with correct firmware update file again.
Before update, make sure if all wirings(communication wire, power wire) are properly connected between IR-USB01 & Servo / between PC and IR-USB01. Then, please do not touch them while updating as it may occur fatal communication error. Please contact factory if communication or update error continues.
From this update, stroke calibration process is added after firmware update. So, before firmware update, make sure if actuator is standalone (should not be connected with any mechanical stuff of your application) for proper calibration.
What are updated?
Before
After
What are updated?
OVERLOAD Protection
Different overload spec per each model
All models overload protection standard are unified and motor cut off under below conditions ;
Continuous operation for more than 30sec. or,
Actuator is stuck at certain point for more than 30sec without position change after goal position command.
Overload protection improvement
Force limit feature removal
Force limit feature (volatile parameter)
Force limit feature removal
To be removed as “Max force”(Non-volatile data) parameter has same function.
“Max force” name change
Previous name has been “Max force”
New name “Motor Operating rate”
To provide more exact definition of this feature
“Motor operating rate” range change
Previously 0~1023 (under the Max force feature)
New range : 400~1023
To be changed to actual operating range.
“Speed” Parameter Removal
Unnatural speed adjustment by Speed parameter
Speed adjustment by “Motor operating rate”. (Force and speed will be adjusted at the same time)
More smooth speed adjustment.
Compliance margin
Compliance margin
Segmentalized to “Start compliance margin” and “End compliance margin”
Improved Stability of position control
Calibration process
Calibration process after firmware update.
Secure exact stroke range
Check Firmware version
Please refer to the old and new firmware number for each servo model.
Firmware version number can be found on mightyZAP manager software. Connect your actuator with software, then see "Management"-"Information" window or "System"-"Firmware version".
If your firmware version is old version, please update it for better performance. (The firmware of actuators which have been delivered after the "Applied" date are already updated. But for sure, please check the firmware version on mightyZAP manager software.
Old Ver.
New Ver.
Applied
(적용일)
D7-6PT-3
Ver. 4
Ver. 5
04-Jun-19
D7-6F-3
-
Ver. 1
04-Jun-19
D7-12PT-3
Ver. 4
Ver. 5
04-Jun-19
D7-12F-3
Ver. 1
Ver. 2
04-Jun-19
D12-6PT-3
Ver. 4
Ver. 5
04-Jun-19
D12-6F-3
Ver. 1
Ver. 2
04-Jun-19
D12-12PT-3
Ver. 4
Ver. 5
04-Jun-19
D12-12F-3
Ver. 1
Ver. 2
04-Jun-19
The end.
-
2019.03.12
New firmware has been released, so please discard below and download newer firmware dated Jul, 22nd, 2019.
Updated firmware for mightyZAP 56mm stroke lineup is just release. To optimize your mightyZAP performance, you are strongly requested to update your old version firmware.
Make sure to download correct model named firmware for your mightyZAP. Download the concerned firmware correctly according to your servo model.
Refer to the update manual. [Manual download]
For firmware update, make sure to install 'mightyZAP manager' software v.1.0.6 on your PC and you need to have IR-USB01 PC USB interface for PC connection.
For those who use older version mightyZAP manager software, here is the download link for 'mightyZAP manager' software v.1.0.6.
Caution
Make sure to download correct model named firmware for your mightyZAP. Download the concerned firmware correctly according to your servo model.
Update single servo only. Do not update with multiple qty of servo motor under serial connection(daisy chain) at the same time. Otherwise, it may occur some error.
In case that incorrect firmware is installed, please process the update with correct firmware update file again.
Before update, make sure if all wirings(communication wire, power wire) are properly connected between IR-USB01 & Servo / between PC and IR-USB01. Then, please do not touch them while updating as it may occur fatal communication error. (please contact factory for this case.)
What is updated?
Update
Before
After
Purpose
PID value improvement
-
PID value Improved
Minimize intermittent jittering at motion end
Overload shutdown level
-
Less sensitive overload shutdown feature
To prolong Overload shutdown trigger time
Input voltage error range
12V lineup
Out of 9V~13V range
More than 13V (Lower input voltage error is removed, but min. voltage should be 6.5V to operate mightyZAP.)
For users who want to use mightyZAP at lower voltage. At lower voltage, force & speed will be lowered too.
7.4V lineup
Out of 6V~8.9V range
More than 8.9V (Lower input voltage error is removed, but min. voltage should be 3V to operate mightyZAP.)
Overload shutdown reset
After overload shutdown, servo motor needs to be turned on again manually.
After overload shutdown, system recovery can be made by "Restart" command.
For easier system recovery after overload protection
Check Firmware version
Please refer to the old and new firmware number for each servo model.
Firmware version number can be found on mightyZAP manager software. Connect your servo motor with software, then see "Management"-"Information" window or "System"-"Firmware version".
If your firmware version is old version, please update it for better performance.
Old Version
New Version
Applied
L12-20PT-6
Version 0
Version 1
25-Feb-19
L12-30PT-6
Version 0
Version 1
25-Feb-19
L12-50PT-6
Version 0
Version 1
25-Feb-19
L12-80PT-6
Version 0
Version 1
25-Feb-19
L12-20F-6
Version 0
Version 1
25-Feb-19
L12-30F-6
Version 0
Version 1
25-Feb-19
L12-50F-6
Version 0
Version 1
25-Feb-19
L12-80F-6
Version 0
Version 1
25-Feb-19
The end.
-
2019.03.12
New firmware has been released, so please discard below and download newer firmware dated Jul, 22nd, 2019.
Updated firmware for mightyZAP 41mm stroke lineup is just release. To optimize your mightyZAP performance, you are strongly requested to update your old version firmware.
Make sure to download correct model named firmware for your mightyZAP. Download the concerned firmware correctly according to your servo model.
Refer to the update manual. [Manual download]
For firmware update, make sure to install 'mightyZAP manager' software v.1.0.6 on your PC and you need to have IR-USB01 PC USB interface for PC connection.
For those who use older version mightyZAP manager software, here is the download link for 'mightyZAP manager' software v.1.0.6.
Caution
Make sure to download correct model named firmware for your mightyZAP. Download the concerned firmware correctly according to your servo model.
Update single servo only. Do not update with multiple qty of servo motor under serial connection(daisy chain) at the same time. Otherwise, it may occur some error.
In case that incorrect firmware is installed, please process the update with correct firmware update file again.
Before update, make sure if all wirings(communication wire, power wire) are properly connected between IR-USB01 & Servo / between PC and IR-USB01. Then, please do not touch them while updating as it may occur fatal communication error. (please contact factory for this case.)
What is updated?
Update
Before
After
Purpose
PID value improvement
-
PID value Improved
Minimize intermittent jittering at motion end
Overload shutdown level
-
Less sensitive overload shutdown feature
To prolong Overload shutdown trigger time
Input voltage error range
12V lineup
Out of 9V~13V range
More than 13V (Lower input voltage error is removed, but min. voltage should be 6.5V to operate mightyZAP.)
For users who want to use mightyZAP at lower voltage. At lower voltage, force & speed will be lowered too.
7.4V lineup
Out of 6V~8.9V range
More than 8.9V (Lower input voltage error is removed, but min. voltage should be 3V to operate mightyZAP.)
Overload shutdown reset
After overload shutdown, servo motor needs to be turned on again manually.
After overload shutdown, system recovery can be made by "Restart" command.
For easier system recovery after overload protection
Check Firmware version
Please refer to the old and new firmware number for each servo model.
Firmware version number can be found on mightyZAP manager software. Connect your servo motor with software, then see "Management"-"Information" window or "System"-"Firmware version".
If your firmware version is old version, please update it for better performance.
Old Version
New Version
Applied
L12-20PT-4
Version 0
Version 1
25-Feb-19
L12-30PT-4
Version 0
Version 1
25-Feb-19
L12-50PT-4
Version 0
Version 1
25-Feb-19
L12-80PT-4
Version 0
Version 1
25-Feb-19
L12-20F-4
Version 0
Version 1
25-Feb-19
L12-30F-4
Version 0
Version 1
25-Feb-19
L12-50F-4
Version 0
Version 1
25-Feb-19
L12-80F-4
Version 0
Version 1
25-Feb-19
The end.
-
2019.03.12
New firmware has been released, so please discard below and download newer firmware dated Jul, 22nd, 2019.
Updated firmware for mightyZAP 27mm(30mm) stroke lineup is just release. To optimize your mightyZAP performance, you are strongly requested to update your old version firmware.
Make sure to download correct model named firmware for your mightyZAP. Download the concerned firmware correctly according to your servo model.
Refer to the update manual. [Manual download]
For firmware update, make sure to install 'mightyZAP manager' software v.1.0.6 on your PC and you need to have IR-USB01 PC USB interface for PC connection.
For those who use older version mightyZAP manager software, here is the download link for 'mightyZAP manager' software v.1.0.6.
Caution
Make sure to download correct model named firmware for your mightyZAP. Download the concerned firmware correctly according to your servo model.
Update single servo only. Do not update with multiple qty of servo motor under serial connection(daisy chain) at the same time. Otherwise, it may occur some error.
In case that incorrect firmware is installed, please process the update with correct firmware update file again.
Before update, make sure if all wirings(communication wire, power wire) are properly connected between IR-USB01 & Servo / between PC and IR-USB01. Then, please do not touch them while updating as it may occur fatal communication error. (please contact factory for this case.)
What is updated?
Update
Before
After
Purpose
PID value improvement
-
PID value Improved
Minimize intermittent jittering at motion end
Overload shutdown level
-
Less sensitive overload shutdown feature
To prolong Overload shutdown trigger time
Input voltage error range
12V lineup
Out of 9V~13V range
More than 13V (Lower input voltage error is removed, but min. voltage should be 6.5V to operate mightyZAP.)
For users who want to use mightyZAP at lower voltage. At lower voltage, force & speed will be lowered too.
7.4V lineup
Out of 6V~8.9V range
More than 8.9V (Lower input voltage error is removed, but min. voltage should be 3V to operate mightyZAP.)
Overload shudown reset
After overload shutdown, servo motor needs to be turned on again manually.
After overload shutdown, system recovery can be made by "Restart" command.
For easier system recovery after overload protection
Check Firmware version
Please refer to the old and new firmware number for each servo model.
Firmware version number can be found on mightyZAP manager software. Connect your servo motor with software, then see "Management"-"Information" window or "System"-"Firmware version".
If your firmware version is old version, please update it for better performance.
Old Version
New Version
Applied
D7-6PT-3
Version 3
Version 4
25-Feb-19
D7-12PT-3
Version 3
Version 4
25-Feb-19
D12-6PT-3
Version 3
Version 4
25-Feb-19
D12-6F-3
-
Version 1
25-Feb-19
D12-12PT-3
Version 3
Version 4
25-Feb-19
D12-12F-3
-
Version 1
25-Feb-19
L7-20PT-3
Version 4
Version 5
25-Feb-19
L7-40PT-3
Version 3
Version 4
25-Feb-19
L7-64PT-3
Version 2
Version 3
25-Feb-19
L7-100PT-3
Version 2
Version 3
25-Feb-19
L12-20PT-3
Version 5
Version 6
25-Feb-19
L12-40PT-3
Version 3
Version 4
25-Feb-19
L12-64PT-3
Version 2
Version 3
25-Feb-19
L12-100PT-3
Version 2
Version 3
25-Feb-19
L12-20F-3
Version 3
Version 4
25-Feb-19
L12-40F-3
Version 3
Version 4
25-Feb-19
L12-64F-3
Version 2
Version 3
25-Feb-19
L12-100F-3
Version 2
Version 3
25-Feb-19
End.
-
2018.10.02
Newer Firmware is released, so discard this announcement and go to the new page.
Updated firmware for mightyZAP 27mm(30mm) stroke lineup is just release. To optimize your mightyZAP performance, you are strongly requested to update your old version firmware.
Make sure to download correct model named firmware for your mightyZAP. Download the concerned firmware correctly according to your servo model.
Refer to the update manual. [Manual download]
For firmware update, make sure to install 'mightyZAP manager' software v.1.0.5 on your PC and you need to have IR-USB01 PC USB interface for PC connection.
For those who use older version mightyZAP manager software, here is the download link for 'mightyZAP manager' software v.1.0.5.
Caution
Make sure to download correct model named firmware for your mightyZAP. Download the concerned firmware correctly according to your servo model.
Update single servo only. Do not update with multiple qty of servo motor under serial connection(daisy chain) at the same time. Otherwise, it may occur some error.
In case that incorrect firmware is installed, please process the update with correct firmware update file again.
Before update, make sure if all wirings(communication wire, power wire) are properly connected between IR-USB01 & Servo / between PC and IR-USB01. Then, please do not touch them while updating as it may occur fatal communication error. (please contact factory for this case.)
What is updated?
Repeatability improvement : Improved to 0.05mm(50μm) from 0.1mm(100μm)
Speed control improvement : Improved for Smoother and more proportional speed control
Overload protection improvement : More realistic overload protection
Check Firmware version
Please refer to the old and new firmware number for each servo model.
Firmware version number can be found on mightyZAP manager software. Connect your servo motor with software, then see "Management"-"Information" window or "System"-"Firmware version".
If your firmware version is old version, please update it for better performance.
Old version
Update version
Applied on
D7-6PT-3
Version 2
Version 3
180810
D7-12PT-3
Version 2
Version 3
180810
D12-6PT-3
Version 2
Version 3
180810
D12-12PT-3
Version 2
Version 3
180810
L7-20PT-3
Version 3
Version 4
180810
L7-40PT-3
Version 2
Version 3
180810
L7-64PT-3
Version 1
Version 2
180810
L7-100PT-3
Version 1
Version 2
180810
L12-20PT-3
Version 4
Version 5
180809
L12-40PT-3
Version 2
Version 3
180809
L12-64PT-3
Version 1
Version 2
180809
L12-100PT-3
Version 1
Version 2
180810
L12-20F-3
Version 2
Version 3
180806
L12-40F-3
Version 2
Version 3
180806
L12-64F-3
Version 1
Version 2
180807
L12-100F-3
Version 1
Version 2
180807
End.
